CERAKOTE C-SERIES GLACIER BLACK (C-7600P) Instruction Manual

1. ভূমিকা

This manual provides detailed instructions for the proper use and application of CERAKOTE C-SERIES GLACIER BLACK (C-7600P) air cure ceramic coating. This product is designed to provide a durable, high-performance finish with exceptional chemical resistance and UV stability on various substrates, including metals and polymers.

CERAKOTE C-SERIES coatings are air-cured and ready to spray, requiring no additional catalyst. The Glacier Black (C-7600) variant offers a deep black, sleek satin finish.

2. নিরাপত্তা তথ্য

WARNING: This product is a chemical coating. Always follow safety precautions.

• বায়ুচলাচল: Use in a well-ventilated area or outdoors. Avoid inhaling vapors.
• ব্যক্তিগত সুরক্ষামূলক সরঞ্জাম (পিপিই): Wear appropriate chemical-resistant gloves, eye protection (safety glasses or goggles), and a respirator suitable for organic vapors.
• ত্বকের সাথে যোগাযোগ: Avoid prolonged or repeated skin contact. Wash thoroughly with soap and water after handling.
• চোখের যোগাযোগ: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and seek medical attention.
• ইনজেশন: গিলে ফেলবেন না। যদি গিলে ফেলা হয়, তাহলে বমি করবেন না। অবিলম্বে চিকিৎসার পরামর্শ নিন।
• জ্বলনযোগ্যতা: Keep away from open flames, sparks, and hot surfaces.
• সঞ্চয়স্থান: Store in a cool, dry place, away from direct sunlight and incompatible materials. Keep container tightly closed when not in use.

3. পণ্য শেষview

The CERAKOTE C-SERIES GLACIER BLACK (C-7600P) is an advanced air-cured ceramic coating formulated for high-temperature applications and environments where extreme durability is required. It provides a deep black, satin finish that maintains its aesthetic and protective qualities under harsh conditions.

মূল বৈশিষ্ট্য:

• Air-cured, ready-to-spray formula.
• No catalyst required.
• Deep black, sleek satin finish.
• Extremely high chemical resistance.
• UV প্রতিরোধী।
• PFAS free formulation.

Figure 1: CERAKOTE C-7600 Glacier Black 16oz bottle. Note the 'C-Series Coating' and 'Glacier Black' labels, and the 'Important: Solids will settle! Must shake well for proper application' warning.

Figure 2: PFAS Free logo, indicating the product's environmental compliance.

4. Setup and Surface Preparation

Proper surface preparation is critical for optimal adhesion and performance of CERAKOTE coatings. Do not skip or rush these steps.

4.1. Required Equipment

• HVLP or conventional spray gun with appropriate nozzle size (e.g., 0.8mm - 1.4mm).
• Air compressor with moisture separator.
• Abrasive blasting equipment (optional, but recommended for optimal adhesion on metals).
• Degreaser (e.g., acetone, MEK, or specialized Cerakote degreaser).
• Clean, lint-free cloths.
• Personal Protective Equipment (PPE) as outlined in Section 2.

4.2. Surface Preparation Steps

1. disassembly: Disassemble the item to be coated into its individual components.
2. ডিগ্রীasing: Thoroughly degrease all surfaces using a suitable degreaser. Ensure all oils, greases, and contaminants are removed. Repeat if necessary.
3. Abrasive Blasting (for Metals): For optimal adhesion on metal substrates, abrasive blast the surface using 100-120 grit aluminum oxide at 80-100 PSI. This creates a profile for the coating to adhere to. Avoid blasting polymers unless specified by the manufacturer.
4. চূড়ান্ত পরিষ্কার: After blasting (if applicable), re-degrease the surface to remove any blasting media residue or new contaminants. Use clean, lint-free cloths.
5. শুকানো: Ensure the surface is completely dry before application. Use compressed air to blow out any crevices.

4.3. Product Preparation

• ভালো করে ঝাঁকান: CERAKOTE C-SERIES coatings contain solids that will settle. Shake the bottle vigorously for at least 5 minutes before use to ensure a uniform mixture.
• No Catalyst: This C-Series product is air-cured and does not require a catalyst. Do not add any.
• Strain (Optional): For best results, strain the coating through a 100-190 micron filter before pouring into the spray gun cup to prevent clogs.

5. Operating Instructions (Application)

Apply CERAKOTE C-SERIES GLACIER BLACK in a controlled environment, maintaining consistent temperature and humidity if possible.

5.1. Spray Gun Settings

• বায়ুচাপ: Typically 20-30 PSI at the gun, depending on the gun type and desired atomization. Adjust as needed for a fine, even spray pattern.
• Fluid Control: Adjust to achieve a consistent flow without excessive material.

5.2. Application Technique

1. Hold the spray gun 4-6 inches (10-15 cm) from the surface.
2. Apply thin, even coats with overlapping passes. Avoid heavy coats, which can lead to runs or uneven curing.
3. Allow 5-10 minutes flash time between coats, or until the surface appears matte and no longer wet.
4. Typically, 1-2 coats are sufficient to achieve full coverage and desired film thickness.
5. Ensure all surfaces are evenly coated.

5.3. Curing Process

• CERAKOTE C-SERIES GLACIER BLACK is an air-cure coating. It will be dry to the touch within 24 hours at ambient temperatures (60-75°F / 15-24°C).
• Full cure and maximum hardness are achieved over a period of 5-7 days. Handle coated items carefully during this initial curing period.
• Do not expose to harsh chemicals or extreme abrasion until fully cured.

6. রক্ষণাবেক্ষণ

Once fully cured, CERAKOTE C-SERIES GLACIER BLACK is highly durable and requires minimal maintenance.

• পরিষ্কার করা: Clean coated surfaces with mild soap and water. Avoid abrasive cleaners or harsh solvents, especially during the initial cure period.
• সুরক্ষা: While highly resistant, avoid unnecessary impact or scratching to preserve the finish.

7. সমস্যা সমাধান

This section addresses common issues that may arise during application.

8. স্পেসিফিকেশন

9. ওয়্যারেন্টি এবং সমর্থন

For specific warranty information regarding CERAKOTE C-SERIES GLACIER BLACK (C-7600P), please refer to the official CERAKOTE website or contact their customer support directly. Warranty terms typically cover manufacturing defects and may vary based on purchase location and application.

গ্রাহক সমর্থন:

• For technical assistance, product inquiries, or support, please visit the official CERAKOTE webসাইট.
• Consult the manufacturer's website for the most up-to-date contact information and detailed application guides.