LCDWIKI CR2019-MI2961 2.4 Inch RPi Display For RPi 3A Plus
পণ্য বৈশিষ্ট্য
- 2.4inch standard display with physical resolution of 320×240
- SPI interface with resistive touch screen for touch control
- perfectly compatible and can be directly inserted into any version of the Raspberry Pi (Raspberry Pi ZeroW, A, A+, B, B+, 2B, 3B, 3B+)
- Support for Raspbian/Ubuntu/Kali systems, Provide driver, image, and online wiki guidance documents
- This product has passed CE and RoHS certification.
পণ্যের পরামিতি
| নাম | বর্ণনা |
| ডিসপ্লে কালার | RGB 65K রঙ |
| এসকেইউ | MPI2411 |
| পর্দার আকার | 2.4 (ইঞ্চি) |
| টাইপ | টিএফটি |
| ড্রাইভার আইসি | ILI9341 |
| পটভূমি আলো | LED |
| রেজোলিউশন | 320*240 (পিক্সেল) |
| সক্রিয় এলাকা | 36.72 × 48.96 (মিমি) |
| মডিউল ইন্টারফেস | এসপিআই |
| টাচ প্যানেলের ধরণ | প্রতিরোধী প্রকার |
| Touch panel control chip | XPT2046 |
| অপারেটিং তাপমাত্রা | -20℃~60℃ |
| স্টোরেজ তাপমাত্রা | -30℃~70℃ |
| অপারেটিং ভলিউমtage | 3.3V / 5V |
| শক্তি খরচ | 0.08A*5V |
| মডিউল পিসিবি সাইজ | 56.00 × 65.00 (মিমি) |
ইন্টারফেস বিবরণ
The pin numbers are as shown below:
| সংখ্যা | মডিউল পিন | পিন বিবরণ |
| 1\17 | 3.3V | Power supply (3.3V power input) |
| 2 \ 4 | 5V | Power supply (5V power input) |
| 3 \ 5 \ 7 \ 8 \ 10 \ 12 \ 16 \ 18 22 | NC | সংযুক্ত নয় |
| 6 \ 9 \ 14 \ 20 \ 25 | জিএনডি | ক্ষমতা স্থল |
| 11 | টিপি_আইআরকিউ | The touch panel is interrupted, and it is detected that the touch panel is pressed low. |
| 15 | এলসিডি_আরএস | Instruction/data register selection |
| 19 | LCD_SI/TP/SI | LCD display / touch panel SPI data input |
| 21 | টিপি_সো | Touch panel SPI data output |
| 13 | LCD_RST | সংকেত রিসেট করুন |
| 23 | এলসিডি_সিসি / টিপি_এসসিকে | LCD display / touch panel SPI clock signal |
| 24 | এলসিডি_সিএস | LCD chip select signal, low level enable |
| 26 | টিপি_সিএস | Touch panel chip select signal, low level enable |
হার্ডওয়্যার কনফিগারেশন
- The LCD module adopts the in-line design, and can be directly inserted into the GPIO port of the RaspberryPi development board according to the wiring requirements, and does not need to be deliberately wired. The module also contains two modules: touch control circuit, LCD display control circuit.
- The touch control circuit is responsible for controlling touch events, including powering the touch control IC, acquiring touch breaks, acquiring ADC values of touch locations, and touch calibration.
- The LCD display circuit is responsible for LCD display control, including GPIO control of the LCD screen, display of color value reading and writing, and register configuration.
ব্যবহারের জন্য নির্দেশাবলী
The First Method
- directly download the system image file we provided, burn it into the micro SD, and then put it on the RaspberryPi. For the specific burning method, see the following file:
http://www.lcdwiki.com/res/PublicFile/How_to_use_Raspberry_Pi(Download,Format,Burn,SSH,PuTTy)-V1.0.pdf - ইমেজ file download can be downloaded from the resource download section of the following URL. http://www.lcdwiki.com/2.4inch_RPi_Display_For_RPi_3A+
The Second Method
- download the latest official system image file
কর্মকর্তা website of each system is as follows:
Raspbian: https://www.raspberrypi.org/downloads/
উবুন্টু: https://ubuntu-mate.org/raspberry-pi/
Kali-linux: https://www.offensive-security.com/kali-linux-arm-images/ - make a system image file
The specific production methods are as follows: http://www.lcdwiki.com/res/PublicFile/How_to_use_Raspberry_Pi(Download,Format,Burn,SSH,PuTTy)-V1.0.pdf - connect to RaspberryPi
Insert the LCD screen holder to the right to insert the Raspberry Pi pin.
Insert the MicroSD card that burns the official system image file, connect the network cable, and connect the power supply. - install LCD driver
Install on the Raspbian system (the Raspberry Pi needs to connect to the Internet)
-
- Open the putty connection ssh, enter the username and password to log in to the Raspberry Pi terminal (the default username and password are shown in the table below).
সিস্টেম ডিফল্ট ব্যবহারকারীর নাম ডিফল্ট পাসওয়ার্ড রাস্পবিয়ান pi রাস্পবেরি Ubuntu-mate pi রাস্পবেরি Kali-linux মূল toor The specific login party see the following file to add the SSH file and use the putty to connect to the RaspberryPi description section:
http://www.lcdwiki.com/res/PublicFile/How_to_use_Raspberry_Pi(Download,Format,Burn,SSH,PuTTy)-V1.0.pdf - After the login is successful, execute the following command (you need to connect the RaspberryPi to the Internet):
sudo rm -rf LCD-show git clone https://github.com/goodtft/LCD-show.gitchmod-R755LCD-showcdLCD-show/sudo./LCD24-show
- Open the putty connection ssh, enter the username and password to log in to the Raspberry Pi terminal (the default username and password are shown in the table below).
Install on the Ubuntu Mate, Kali system
- Download the local driver(Because of system differences, the driver downloaded from github cannot run normally in the two systems Ubuntu Mate, Kali, so only local drivers can be used)
The local driver download can be found in the LCD driver section of Method 2 used in the Raspberry/Rbbian/Ubuntu Mate/Kali system on the following page. http://www.lcdwiki.com/2.4inch_RPi_Display_For_RPi_3A+ - Open the putty connection ssh, enter the username and password to log in to the Raspberry Pi terminal (the default username and password are shown in the table below).
The specific login party see the following file to add the SSH file and use the putty to connect to the RaspberryPi description section:সিস্টেম ডিফল্ট ব্যবহারকারীর নাম ডিফল্ট পাসওয়ার্ড রাস্পবিয়ান pi রাস্পবেরি Ubuntu-mate pi রাস্পবেরি Kali-linux মূল toor - Copy the local driver to the running Raspberry Pi system and execute the following command to extract it (can be copied by SD card or FileZilla software)
tar –xvzf LCD-show.tar.gz - Execute the following command to install the LCD driver
chmod -R 755 LCD-show cd LCD-show/
sudo ./LCD24-শো - Check if the driver is successfully installed
After the LCD driver is installed, the system will automatically restart. After the startup is successful, the LCD can display and touch normally,indicating that the driver installation is successful.
দ্রষ্টব্য:
- The setting method of ubuntu system login through SSH is as follows: http://www.lcdwiki.com/res/PublicFile/RaspberryPi_Ubuntu-mate_Open_SSH_Instructions_EN.pdf
- The solution to the ubsh connection failure of ubuntu-18.04 system is as follows: http://www.lcdwiki.com/res/PublicFile/RaspberryPi_Ubuntu-mate-18.04_SSH_Connect_EN.pdf
সিস্টেম ব্যবহার করে
- Switch back to HDMI display
Switch to the HDMI display by entering the following command:
sudo ./LCD-hdmi - calibration resistance touch screen
The specific calibration method is as follows: http://www.lcdwiki.com/res/PublicFile/How_to_calibrate_the_resistance_touch_screen-V1.2.pdf - modify the display direction and GPIO resistance touch screen parameters
The specific calibration method is as follows: http://www.lcdwiki.com/res/PublicFile/How_to_change_display_direction-GPIO-Resistive_Touch-V1.2.pdf
Scan the QR Code For more details 
প্রায়শই জিজ্ঞাসিত প্রশ্নাবলী
What systems are supported by the product?
The product supports Raspbian, Ubuntu, and Kali systems for Raspberry Pi ZeroW, A, A+, B, B+, 2B, 3B, and 3B+ models.
Is there touch panel functionality on the display?
Yes, the display features a resistive touch panel controlled by the XPT2046 chip.
দলিল/সম্পদ
 |
LCDWIKI CR2019-MI2961 2.4 Inch RPi Display For RPi 3A Plus [পিডিএফ] ব্যবহারকারী ম্যানুয়াল MPI2411, 3A, CR2019-MI2961 2.4 Inch RPi Display For RPi 3A Plus, CR2019-MI2961, 2.4 Inch RPi Display For RPi 3A Plus, Display For RPi 3A Plus, RPi 3A Plus, 3A Plus |